BRICKS

Brick is obtained by moulding good clay into a block, which is dried and then burnt. This is the oldest building block to replace stone. Manufacture of brick started with hand moulding, sun drying and burning in clamps. A considerable amount of technological development has taken place with better knowledge about to properties of raw materials, better machineries and improved techniques of moulding drying and burning. The size of the bricks are of 90 mm × 90 mm × 90 mm and 190 mm × 90 mm × 40 mm. With mortar joints, the size of these bricks are taken as 200 mm × 100 mm × 100 mm and 200 mm × 100 mm × 50 mm.

Types of Bricks
Bricks may be broadly classified as:

(i) Building Bricks: These bricks are used for the construction of walls.
(ii) Paving Bricks: These are vitrified bricks and are used as pavers.
(iii) Fire Bricks: These bricks are specially made to withstand furnace temperature. Silica bricks belong to this category.
(iv) Special Bricks: These bricks are different from the commonly used building bricks with respect to their shape and the purpose for which they are made. Some of such bricks are listed below:
(a) Specially shaped bricks
(b) Facing bricks
(c) Perforated building bricks
(d) Burnt clay hollow bricks
(e) Sewer bricks
( f ) Acid resistant bricks.
(a) Specially Shaped Bricks: Bricks of special shapes are manufactured to meet the
requirements of different situations.Some of them are shown in Fig

(b) Facing Bricks: These bricks are used in the outer face of masonry. Once these bricks are provided, plastering is not required. The standard size of these bricks are 190 × 90 × 90 mm or 190 × 90 × 40 mm.

(c) Perforated Building Bricks: These bricks are manufactured with area of perforation of 30 to 45 per cent.The area of each perforation should not exceed 500 mm2. The perforation should be uniformly distributed over the surface. They are manufactured in the size 190 × 190 × 90 mm and 290 × 90 × 90 mm

(d) Burn’t Clay Hollow Bricks: Figure 1.4 shows a burnt clay hollow brick.They are light in weight. They are used for the construction of partition walls. They provide good thermal insulation to buildings. They are manufactured in the sizes 190 × 190 × 90 mm,290 × 90 × 90 mm and 290 × 140 × 90 mm.The thickness of any shell should not be less than 11 mm and that of any web not less than 8 mm.

(e) Sewer Bricks: These bricks are used for the construction of sewage lines. They are manufactured from surface clay, fire clay shale or with the combination of these. They are manufactured in the sizes 190 × 90 × 90 mm and 190 × 90 × 40 mm. The average
strength of these bricks should be a minimum of 17.5 N/mm2 . The water absorption should not be more than 10 per cent.
( f ) Acid Resistant Bricks: These bricks are used for floorings likely to be subjected to acid attacks, lining of chambers in chemical plants, lining of sewers carrying industrial wastes etc. These bricks are made of clay or shale of suitable composition with low lime and iron content, flint or sand and vitrified at high temperature in a ceramic kiln.

Properties of Bricks
The following are the required properties of good bricks:
(i) Colour: Colour should be uniform and bright.
(ii) Shape: Bricks should have plane faces. They should have sharp and true right angled corners.
(iii) Size: Bricks should be of standard sizes as prescribed by codes.

(iv) Texture: They should possess fine, dense and uniform texture. They should not possess fissures, cavities, loose grit and unburnt lime.

(v) Soundness: When struck with hammer or with another brick, it should produce metallic sound.

(vi) Hardness: Finger scratching should not produce any impression on the brick.
(vii) Strength: Crushing strength of brick should not be less than 3.5 N/mm2. A field test for
strength is that when dropped from a height of 0.9 m to 1.0 mm on a hard ground, the brick should not
break into pieces.
(viii) Water Absorption: After immercing the brick in water for 24 hours, water absorption should
not be more than 20 per cent by weight. For class-I works this limit is 15 per cent.
(ix) Efflorescence: Bricks should not show white patches when soaked in water for 24 hours and
then allowed to dry in shade. White patches are due to the presence of sulphate of calcium, magnesium
and potassium. They keep the masonry permanently in damp and wet conditions.
(x) Thermal Conductivity: Bricks should have low thermal conductivity, so that buildings
built with them are cool in summer and warm in winter.
(xi) Sound Insulation: Heavier bricks are poor insulators of sound while light weight and hollow
bricks provide good sound insulation.
(xii) Fire Resistance: Fire resistance of bricks is usually good. In fact bricks are used to encase
steel columns to protect them from fire.